TasDia Network
TasDia Network

MCQs 1: The relation between intensity of wind pressure p and velocity of wind V is taken as_______________?

pa V paV2 p a (1/V) paV”2
Answer Explanation

MCQs 2: The internal pressure coefficient on walls for buildings with large permeability is taken as_______________?

± 0.2 ±0.5 ± 0.7 0
Answer Explanation

MCQs 3: The risk coefficient k, depends on__________________?

mean probable design life of structures basic wind speed both (A) and (B) none of the above
Answer Explanation

MCQs 4: Area of openings for buildings of large permeability is more than_________________?

10% of wall area 20% of wall area 30% of wall area 50% of wall area
Answer Explanation

MCQs 5: The number of seismic zones in which the country has been divided are_________________?

3 5 6 7
Answer Explanation

MCQs 6: The allowable tensile stress in structural mild steel plates for steel tank is assumed as________________?

95.0 MPa on net area 105.5 MPa on net area 105.5 MPa on gross area 150.0 MPa on gross area
Answer Explanation

MCQs 7: Which of the following sections should preferably be used at places where torsion occurs ?

angle section channel section box type section any of the above
Answer Explanation

MCQs 8: The bracing between two columns of a steel tank will be designed to resist_________________?

horizontal shear due to wind or earthquake only horizontal, shear due to wind or earthquake + 2.5% of column loads column loads + 2.5% of horizontal shear due to wind or earthquake column loads + full horizontal shear due to wind or earthquake
Answer Explanation

MCQs 9: Maximum pitch of rivets, used in steel stacks, is limited to_______________?

6t 101 121 161
Answer Explanation

MCQs 10: If the floor is supported at or near the bottom but top chords of a bridge are not braced, then the bridge is called________________?

deck type through type half through type double deck type
Answer Explanation

MCQs 11: The effect of racking forces is considered in the design of_________________?
i) lateral braces
ii) chord members
The correct answer is

only (i) only (ii) both (i) and (ii) none of the above
Answer Explanation

MCQs 12: The sway bracing is designed to transfer____________________?

2Vi % of the top panel wind load to bottom bracing 10% of the top panel wind load to bottom bracing 25% of the top panel wind load to bottom bracing 50% of the top panel wind load to bottom bracing
Answer Explanation

MCQs 13: The bracing provided in the plane of end posts is called__________________?

sway bracing portal bracing top lateral bracing bottom lateral bracing
Answer Explanation

MCQs 14: The least dimension in case of a circular column of diameter D is taken as_______________?

0.5 D 0.68 D 0.88 D D
Answer Explanation

MCQs 15: In case of timber structures, the simple bending formula M = fz may be applied for________________?

rectangular beams up to 300 mm depth all rectangular beams solid circular beams only all square cross-section beams
Answer Explanation

MCQs 16: The mechanism method and the statical method give__________________?

lower and upper bounds respectively on the strength of structure upper and lower bounds respectively on the strength of structure lower bound on the strength of structure upper bound on the strength of structure
Answer Explanation

MCQs 17: Shape factor is a property which depends________________?

only on the ultimate stress of the material only on the yield stress of the material only on the geometry of the section both on the yield stress and ultimate stress of material
Answer Explanation

MCQs 18: The mechanism method of plastic analysis satisfies___________________?

equilibrium and mechanism conditions equilibrium and plastic moment conditions mechanism and plastic moment conditions equilibrium condition only
Answer Explanation

MCQs 19: The ratio of plastic section modulus to elastic section modulus__________________?

is equal to 1 is always less than 1 is always greater than 1 can be less than 1
Answer Explanation

MCQs 20: Which of the following conditions is to be satisfied both in elastic and plastic analysis ?

equilibrium condition yield condition plastic moment condition mechanism condition
Answer Explanation

Related Topics

About Us | Contact Us | Privacy Policy
ABOUT US
Category
Who We Are

TasDia Network, this platform not only provides you the best educational stuff but besides this, we are creating thousands of new ideas to making your signature and planning much more on a single platform.

© 2020-2023, TasDia Network

All rights of the publication are reserved by tasdia.com.